Planar C3013T Bedienungsanleitung Seite 30
- Seite / 60
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Boot Sequence Sub-Menu (under Main Menu)
The Boot Sequence sub-menu accesses Boot Options.
Figure 18 — Boot Sequence sub-menu.
Boot Delay
This option sets the system to delay booting for a time period in seconds. It allows for long
startup times on boot devices that spin up slowly, and it ranges from 0–255 seconds. The default
is 0 seconds.
Boot Sequence
This defines how the system treats floppy drive A when booting. Booting can occur from a flop-
py in the A drive or directly from the fixed disk drive. To reduce the amount of time required
to boot, the boot sequence should be set to C: only. The options are:
1. A: then C: Boots from the floppy drive, or if no floppy disk is present in the A drive, boots
from the C drive.
2. C: then A: Boots from the C drive, or if none is present, boots from the A drive.
3. C: only: Boots from the C drive without searching for an A drive.
The default is A: then C:. The selected boot sequence setting displays in the Boot Sequence
sub-menu field in the Main menu (see Figure 17).
SETUP Prompt
This option enables or disables the message Press F2 to enter Setup. Even if the message is dis-
abled, the <F2> key can still be pressed at the appropriate time to enter the Setup menu. The
default is Enabled.
POST Errors
This option stops the boot process if the POST encounters errors. Otherwise, the system contin-
ues to attempt to boot despite any startup error messages that display. Note that this option only
affects those errors defined at build-time to halt the system. The default is Enabled.
Chapter Five: BIOS Setup 19
CS Manual LAYOUT#1787 3/9/98 5:33 PM Page 19
- Planar Clean Screen 1
- User’s Manual 1
- USER’S MANUAL 2
- REGULATORY INFORMATION 4
- WARRANTY INFORMATION 4
- Limitation of Warranty 5
- Technical Assistance 5
- Installation 5
- Table of Contents 6
- INSTALLATION GUIDE 9
- Safety Instructions 10
- Front Panel 11
- Connections (Bottom) 11
- Clean Screen Facts 13
- Back Housing 15
- Replacement 17
- Figure 9 18
- Installing Memory 19
- To remove an SO DIMM module 19
- To install a SO DIMM module 19
- Replacing the Hard Disk Drive 20
- Installing the new hard disk 20
- Replacing the Battery 21
- Replacing the Fuses 22
- Mounting the Clean Screen 23
- Chapter Four: System Setup 24
- Chapter Four: System Setup 15 26
- Chapter Five: BIOS Setup 27
- Chapter Five: BIOS Setup 17 28
- Chapter Five: BIOS Setup 19 30
- Floppy Check 31
- Summary Screen 31
- Chapter Five: BIOS Setup 21 32
- BIOS Extensions 33
- BIOS Extension Offset in FBD 33
- Destination Address 33
- BIOS Extension Size 33
- Chapter Five: BIOS Setup 23 34
- Touch Panel Base Address 35
- Touch Panel IRQ 35
- Local Bus IDE Adapter 35
- Chapter Five: BIOS Setup 25 36
- Standby Wakeup Events 38
- Keyboard 38
- Figure 22 — Exit menu 39
- Restore Condition 40
- Clear Over Temperature Error 40
- Maintenance Tips 41
- Cleaning Tips 41
- REFERENCE GUIDE 42
- Environmental Specifications 44
- Power Supply 44
- Com2 Com1 Real IDE 45
- I/O Address List 46
- Appendix C: Troubleshooting 47
- Boot Failures 48
- Problems and Suggestions 52
- Resetting the System 57
- CMOS Configuration 58
- Appendix E: Technical Support 59
BOLEX Proyectores manuales de usuario
La lista de productos de BOLEX Proyectores contiene 4 manuales de usuario para 2 seleccionados. Todas las guías de usuario en pdf están disponibles para descargar o ver en línea.
Kommentare zu diesen Handbüchern